| OPTION CODE |
OPTION DESCRIPTION |
| PHRA1010 |
Obstruction Safety Photoeye System For PRTA 2100 & 2150
- If the safety hoop located in front of the rotating arm is deflected by a pallet out of position or other objects, the safety photeye reads this deflection and immediately stops the wrapping system to prevent any damage to the equipment.
|
| PHAE1003 |
460 0R 575 vac Power Transformer for Automatic System
- If the safety hoop located in front of the rotating arm is deflected by a pallet out of position or other objects, the safety photeye reads this deflection and immediately stops the wrapping system to prevent any damage to the equipment.
|
| PHAE1001 |
A.B. MicroLogix 1500 PLC for Automatic System
- Replaces Standard Omron PLC.
|
| PHAE1002C |
A.B. (Allen Bradley) Power Flex VFD's for PRTA 2100 & 2150
- 230vac 3 Phase 60 hz Allen Bradley Power Flex 4 Series VFD's control the motors that are used for the machine.
- Replaces standard Omron VFD's.
|
| PHAM1000 |
Low Film Alarm
- A photoeye system mounted on the carriage that detects when the film roll has depleted to a certain level.
- The "film out" beacon on the panel will strobe to indicate that the film is close to being finished.
|
| PHRA1011 |
18 RPM High Speed Rotation For Phoenix PRTA-2150 Includes:
- 18 RPM rotation speed for arm rotation.
- Double boom rotation arm frame.
- 1 1/2 hp rotation drive system.
- Dual chain carriage lifting system.
|
| PHAC1001A |
5 Ft Powered Roller Conveyor wit VFD Control
Includes:
- All electrical controls.
- Photoeye load positioning.
- Standard load sequence programming.
- 2 1/2" dia. x 3 3/4" centers 11 ga rollers.
- 52" BFR.
- 4,000 Lbs Maximum Capacity.
- 18" Pass Height.
- Every roller driven, loop to loop design.
- Enclosed chain guard around rollers.
- 230vac Motor with Omron VFD Control.
|
| PHAC1001 |
5 Ft Powered Roller Conveyor wit DC Control
Includes:
- All electrical controls.
- Photoeye load positioning.
- Standard load sequence programming.
- 2 1/2" dia. x 3 3/4" centers 11 ga rollers.
- 52" BFR.
- 4,000 Lbs Maximum Capacity.
- 18" Pass Height.
- Every roller driven, loop to loop design.
- Enclosed chain guard around rollers.
- 90 vdc Motor with Controller for Soft Start/Stop.
|
| PHRA1008 |
18" to 24" Pass Height for Rotary Tower System
- Standard is 18".
- Includes Base Machine Only.
|
| PHRA1008A |
24" to 36" Pass Height for Rotary Tower System
- Standard is 18".
- Includes Base Machine Only.
|
| PHRA1008B |
36" to 42" Pass Height for Rotary Tower System
- Standard is 18".
- Includes Base Machine Only.
|
| PHAC1000 |
Forklift Loading/Unloading Station (Photo-Eye)
- A safety photoeye mounted under the conveyor detects when the forklift breaks the photoeye beam as it approaches the zone.
- The conveyor is not able to run until the forklift has left the station. This allows the pallet load to be placed or picked up without the conveyor automatically indexing. (Very important for side loading applications).
|
| CONV1019 |
Non Std. Conveyor Speed Of 45- 60 FPM For System
- Requires change of drive systems for all conveyors.
|
| PHAC1003 |
Forklift Bumper Guard To Protect Conveyor From Damage
- A stand alone floor mounted guard assembly is anchored to the floor in front of the conveyor to prevent forklifts from hitting the side of the conveyor when loading or unloading pallets.
- The height of the guard is such that it also prevents the forks from driving down into the rollers, damaging their conveying performance.
|
| PHAC1004 |
5 Ft Long Gravity Roller Conveyor
- 2 1/2 " diameter rollers on 3" centers.
- 52 BFR Effective Width.
- 18" pass height.
- 4,000 lbs. capacity.
- Pallet accumulation PE.
- End stop bumper.
|
| PHAC1004A |
10 Ft Long Gravity Roller Conveyor
- 2 1/2 " diameter rollers on 3" centers.
- 52 BFR Effective Width.
- 18" pass height.
- 4,000 lbs. capacity.
- Pallet accumulation PE.
|
| PHRT1004 |
Dark Load Special Auto-Height Photo Eye
- Replaces standard photoeye.
- Background suppression for dark (black, green, brown colours) and/or shiny loads.
|
| PHRA1000A |
Film Tail Anvil Heat Sealer (PRTA)
- Replacing the traditional film clamp and cut system this positive film tail sealer works on the principle of pressure and heat time to provide a secure film attachement to the pallet load.
- Anvil pad raises to provide the sealing surface, function of the heater/ cutter is not load dependant.
- Mounted to the side of the wrap zone conveyor and is pneumatically driven.
|
| PHTA1014A |
Phoenix Integral Top Sheet Dispenser For PRTA System
Water Tight Cycle:
- When top sheet application is selected the stretch wrapper starts a normal cycle and spirals wrapping the product to the top. After applying a top wrap, the wrapping cycle pauses as the top sheet dispenser applies a top sheet, cuts the top sheet to the required length, and then applies the sheet over the top of the load. The wrapper then continues its cycle by overwrapping the top sheet and locking it in place before spiraling down to complete the cycle. As the top sheet is applied over the top of the side layers any water will run off the top sheet and flow down the outside of the "shingled" side layers.
Includes:
- Manual controls for cradle jog up/down.
- Photoeye for Autoheight Sensing. (to max. 80" std.).
- Load sheet detection.
- Flying knife cuts the poly film to the correct length.
- Ability to run 60" to 72" maximum width film.
- Pneumatic actuated clamp pull-out for sheet dispensing.
- T.S. cradle capacity based on 2 mil - 5 mil thickness range, roll weight not to exceed 200 lbs.
|
| PHTA1015 |
Inline Top Sheet Dispenser System
- Includes extra length on infeed conveyor that is required.
|
| PHRA1007 |
Electric Top Platen for Variable Load Height - PRTA Machines
Stabilizes unstable loads for wrapping. The top platen is automatically lowered down onto the top of the product to be wrapped once it stopped its transition into the wrap zone. The platens foam covered pad ensures that the load will not tip or move during the wrapping cycle. With the load fully secured, the wrapping cycle can commence. Once wrapped, the top platen is raised to allow for pallet to transition out of the wrapping area.
- Foam padded top platen 36" dia. (other sizes possible based on application).
- Chain drive lifting system.
- Standard holding range; 24" to 80" tall.
- Includes open center slip ring to allow the Platen to move through the center of the ring bearing.
|
| CONV1055 |
Dual Conveyor Speed On Infeed
- loads entering stretch wrapping system from upstream conveyor at 30 ft/min will be conveyed into wrap zone at 60 fpm.
|
| AUTO1025 |
Extra Copies of Operation & Maintenance Manual
Includes:
- Electrical schematics and PLC program on diskette.
- Exploded "3-D" assembly views for easy parts identification.
Manual can be issued in "hardcopy" or "CD-ROM" format. To be specified at time of order. |
| MISC1038 |
"E Stop" Electrical Air Dump Safety Valve
- Dumps all air pressure to system if "E-Stop" button is pushed.
|
| PHRA1009 |
Air Conditioner for Panel For 104° F to 130° F Temp.
- An air conditioner is mounted inside the control cabinet in operating environments between 104 degrees F to 130 degrees F.
|
| ELEC1022 |
Extra Control Interlock Relay
- Provides an interlocked relay contact closure from an input (or output) signal for a customer supplied requirement.
|
| AUTO1022 |
Isolation Transformer To Protect PLC From Voltage Spikes |
| PHRT1001 |
30" Powered Pre-Strech Film Carriage Upgrade
- Replaces standard 20" carriage.
|
| PHRT1016 |
20" Film Adaptor on 30" Carriage
- Allows the operator to run 20" film on a 30" carriage frame.
|
| PHAE1000 |
Remote Access Modem Package
The modem package allows for remote access to the Stretchwrapper PLC reducing support costs with the ability to:
- Perform Programming modifications:
- Troubleshoot and debug.
- Monitor the program to quickly isolate and identify a problem.
|
| PHRA1003A |
Safety Fence Upgrade c/w Dual Channel Monitoring
- Modified safety fencing panels for 96" tall and 6" from ground, surrounds the full stretch-wrapping process area.
- Access door is electrically interlocked for safety lockout with dual channel monitoring relay.
Does not include Light Curtains if required.
|
| PHAE1008 |
Electric Barrier Light Curtain For Automatics
- Muting eyes on either side of the barrier are included.
|
| PHAM1002 |
Thermo Bar Film Cutter Upgrade
- No moving parts as with the cut wire that will wear and eventually fail.
|
| PHRA1003C |
Additional Safety Fence c/w Dual Channel Monitoring
- Modified safety fencing panels for 96" tall and 6" from ground.
|
| PHRA1003B |
Additional Safety Fence
- Full height (6ft.) wire mesh safety fence.
|
| PHRA1012 |
Credit for System Conveyor Included with PRTA Automatic
- Removes conveyor and related electrical controls
|
| PHRA1012A |
Credit for Center Wrap Zone Conveyor Included with PRTA Automatic
- Removes conveyor and related electrical controls
|
| PHRA1013 |
Single "Rope Down" Pmeumatic Roping On PRTA Automatics
- A pneumatic cylinder with a roping assembly is mounted on the film carriage.
During the cycle, a solenoid valve activates the roping mechanism allowing the film to be gathered, forming a rope at the bottom of the carriage frame.
- This reinforces the film to the pallet, in the case of tab folding, holds the tabs to the load more securely than just a film web.
- Includes roping on/off control on the panel.
|
| PHRT1024 |
Rotary Arm Extended for 92" Wrap Dia.
- One foot extension on wrap diameter.
- Includes required extension to wrap zone conveyor.
|
| PHRT1024A |
Rotary Arm Extended for 104" Wrap Dia.
- One foot extension on wrap diameter.
- Includes required extension to wrap zone conveyor.
|
